ProTek RC "TruTorque" Metric 1/4" Power Drill Tip Set (4) (1.5, 2.0, 2.5, 3.0mm)
About this part
This is a ProTek R/C "TruTorque" Metric Power Tool Tip Set, with 1.5, 2.0, 2.5 and 3.0mm tips. No one wants to spend money on low quality tools. Tools are an investment that should not be taken lightly and are one of the few items that should outlast the life of the model you are working on...and remain with you for years after. With so many choices available, the decision can be overwhelming. So ProTek R/C has stepped up again, expanding its product line with a complete range of affordable, high quality tools that help to make the decision a little easier.
Anyone who has used a cordless drill to wrench on their rig knows that when used properly, power tools can provide an incredible advantage. They not only allow you to replace damaged parts faster, but also help to prevent hand fatigue. ProTek R/C "TruTorque" Power Tool Tips are machined from high quality HSS steel for durability and long life. The precision cut tips provide an exceptional fit with the fastener. The 1/4" drive hex ends are designed to fit tools that accept a 1/4" drive hex socket.
When it comes to high quality products that are backed by incredible customer support, ProTek R/C has you covered with the products you need to keep your rig ready for action, no matter what.
Features:
- Quality tool steel tips
- Standard 1/4" drive for compatibility with common power tools
- Size is marked on the tip for identification
Total Length: 85mm
Tip Length: 54mm
Material: HSS Steel
Includes:
- (1) 1.5mm 1/4" Drive Power Tool Tip
- (1) 2.0mm 1/4" Drive Power Tool Tip
- (1) 2.5mm 1/4" Drive Power Tool Tip
- (1) 3.0mm 1/4" Drive Power Tool Tip
Click Here For Warranty Information
ProTek R/C is an AMain Sports & Hobbies brand
CA Residents Prop 65 Warning
WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov Details...Reviews3.5 · 30 reviews
These tools key in really well with my hardware. However I am extremely disappointed in them. The shaft spins in the nut on the end very easily. All four in my first set went after tightening 1 screw each! Amain replaced them however the new set did exactly the same. Should have sent more on a different brand!
Not happy with this set at all. I used the 2.0 hex un-screwing. On the fifth screw the tip broke off, not to mention it was machined crooked to begin with. Not so happy with the brand protek. I will be calling for a refund or upgrade of some sort
These hex are cheap in quality. I purchased a set and striped out two of the hexes. I have had other brands for years and still no issues. What a waste of money. I'll never buy protek again.
WAY too soft. Being careful I rounded the edges in the equivalent of taking the bolts out of a tlr 22 chassis twice. Much better options out there.
Protek TruTorque 2.0 Power Tool Tips: Overall 4.5 of 5 Stars. Ive had this set for a little over a year now, still working great with no issues. I believe the bad reviews could have had the older Gen 1 (Brown-Colored Shafts) TruTorque which admittedly were pretty poor. While not quite as strong as MIP, these TruTorque 2.0 Tips are a very close 2nd place and will last just as long as MIP in 95% of cases, and are even made from similar steel. Ive even used these tips in a Milwaukee M18 (18V) Fuel Gen 3.5 1/4-in Impact Driver and not stripped them out. This makes them a far better value than MIP with a much higher performance-to-cost ratio. At this point they are finally showing a bit of wear but are still working without slipping. The shafts are no longer perfectly straight either, but again they work fine. To be honest, I have abused them quite badly. Ive used them as pry bars to pull things off, sometimes with so much force I was scared I was going to snap them. Using them in an 18V Brushless Impact wasn't the best idea either. But this just shows me that they are worth the money. So I say try them, I am sure you won't be disappointed especially considering the cost VS MIP.
Reviews of the ProTek RC TruTorque 1/4" metric hex tip set (1.5, 2.0, 2.5, 3.0mm) are sharply divided. Many buyers report good fit, sharp and durable hardened steel, and heavy use in drills and impact or electric drivers without stripping, with some noting it is good value. Others report tips breaking or stripping, with the 1.5mm and 2.0mm sizes most often cited, along with loose fit, crooked shafts, and a press-fit section separating. Several reviewers note that older negative reviews may reflect an earlier generation or production batch, while others say current-looking units still failed. Reported failures often occurred soon after first use, and some buyers received replacements that behaved the same way.
- + Sharp, accurate hex fit
- + Hardened steel holds up for many buyers
- + Good value for the price
- + Works well in drills and electric drivers
- − Tips break or strip in some units
- − 2.0mm and 1.5mm tips frequently cited as failing
- − Some shafts arrive crooked
- − Loose fit or press-fit section separates on some units