Parts/Drivetrain/Drivetrain hardware (hex hubs, pins)/Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)
Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)
Traxxas

Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)

Part # TRA6856X3.1(7)
Where to buy
$35.95
AMain Hobbies
Seen Oct 12, 2026
$35.95Buy
Prices are as last seen at the store; stock is not tracked.

About this part

This is an optional Traxxas Aluminum 17mm Wheel Adapter Set, and is intended for use with the Traxxas Slash 4x4 truck. This kit includes all the components necessary to convert your truck to 17mm 1/8 scale off-road tires including hubs, hub retainers, wheel pins, splined 17mm wheel nuts and an allen wrench for installation.

Reviews3.1 · 7 reviews

radley kaveon Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)

This kit works perfectly I have been bashing on it installed on my stampede 4x4 for some time now and it has performed flawlessly love it!

5 found this helpful
AnonymousVerified owneron Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)

Do not buy this! this part is pretty useless and and made from cheap aluminium.

5 found this helpful
Andrew PopeVerified owneron Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)

fit perfect on my rustler vxl to put nice foam tires for speed runs

2 found this helpful
Auxgearboxon Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)

These work well, but Traxxas puts a lot of thread lock on the 17mm wheel hub threads from the factory. If you don't clean up the threads, you risk stripping the 17mm aluminum wheel nuts. Tip, before installing your 17mm wheels for the 1st time: Heat up the thread lock, on the wheel hub threads, with a lighter or torch for about 15 - 30 seconds...Then thread the nut on (carefully), without burning yourself. Repeat as necessary, for each hub. Use a wrench or pliers to hold the 17mm hex that the wheel would ride on, to keep drive line from spinning, while chasing the wheel nut on & off the hub. This should clean up the threads enough to install your wheels, while keeping the benefit of the thread lock.

1 found this helpful
TaylorVerified owneron Traxxas Aluminum 17mm Wheel Adapter Set (Blue) (4)

After 3 battery cycles, I think it's safe to say I'm pretty well satisfied with this kit that I'm using with a set of MX28 Pro-line Badlands tires. These seem well made, they fit very snug and holds tight. I would caution against NOT using locktite and letting that seal for a few hours at the minimum. My adapter set seems just fine after I let the locktite sit on the screw threads for a while and then I took it out on various terrain. Another important note I should add is to be very careful to thread the included blue fasteners slowly so it won't catch sideways and twist...it takes a bit of patience to get them perfectly threaded, but once you do so, just get a 17mm socket and ratchet it until it's well tightened onto the wheel. Same goes for the screws that go through the center of the adapter and onto the drifeshaft theads at the end--again, locktite is your best friend, and make sure to get those well tightened in. These are a little on the pricey side, but it's not a bad deal either. I'm certainly happy with them and would purchase again.

What reviewers say

Reviewers are divided on this Traxxas 17mm aluminum wheel adapter set. Several report it fits well and performs reliably on Stampede 4x4 and Rustler VXL trucks, including with foam and Badlands tires, and one notes it held up over several battery cycles. Others report the parts are cheap or poorly made, with one owner saying every set they bought cross-threaded from the start. A recurring issue is factory thread-locker on the hub threads, which can strip the aluminum nuts unless the threads are cleaned or heated before first install. Reviewers suggest using thread-locker and threading the blue fasteners slowly. One review is off-topic and unrelated to the product.

  • + Fits snugly on compatible trucks
  • + Performs reliably in use
  • + Works with foam and Badlands tires
  • − Threads cross or are poorly made on some sets
  • − Factory thread-locker can strip nuts without cleaning
  • − Aluminum feels cheap to some owners
Summary generated from the reviews above.

Builds using this part

No builds use this part yet — add it to yours from the build editor.